|
HHO Hydrogen Generator 2 Cell Kit Complete Water4Gas
This Listing is for a Complete
KempCo-HHO
2-Cell “High Output” System
This Hydrogen on Demand System includesThe Fully Assembled “Starter” Generator Cell
with Safety Check Valve
and One Fully Assembled “Add-On” Generator Cell
Plus
our “Dual Supply” Hook-Up Kit
(see full list below)
Also, to Inter-Link your System, we’ll throw in the
Vacuum Hose and Twist~Connects
&
Daisy Chain Wire and Terminals!
For Frequently Asked Questions
See our store Page here
WHY USE A MULTI-CELL SYSTEM?
Like many other HHO producers, we’ve borrowed the following from Patrick Kelly’s document “D9.PDF”, as it is printed in the “Water4Gas” guide. Mr. Kelly has done all the mathematical homework for us in this excerpt:
The current flowing through the cell determines its HHO production. This is an absolute key factor in gas production, and one of the most difficult to control accurately and economically. The greater the current, the greater the rate of gas production. The current is controlled by the concentration of Baking Soda in the water and the voltage across the cell. The voltage across the cell has limited effect as it reaches a maximum at 1.24 volts. Up to that point, an increase in voltage causes an increase in gas production rate. Once the voltage gets over this limit, increasing it further produces no further increase in the rate of gas production. If the voltage is increased above 1.24 volts, the extra voltage goes to heat the water. This can be a slight advantage, but not much. (The advantage is that heat creates more water vapor which is good for cooling down the engine.) Let’s look at the math. We’ll simplify it here for the sake of understanding. Assume that the current through the cell is 2 amps. In that case, the power used to produce gas is 2 amps x 1.24 volts = 2.48 watts. When the engine is running, the voltage at the car’s battery terminals will be about 13.8 volts as the alternator provides the extra voltage to drive current into the battery. The excess voltage applied to the cell is about 1.24 less than that, or 12.56 volts. The power which heats the electrolyte is now 12.56 volts x 2 amps = 25.12 watts. That is more than ten times the power being used to produce gas! This is very inefficient. In short: The more cells, the less heat and more HHO. Or, more correctly, higher energy efficiency for HHO production. This is true up to 6 or 7 cells max. (Although KempCo has run more)
So…with a Multi-Cell System, you’re dividing the currentwhich keeps the heat down, allowing you to add more catalystto produce even more HHO, and at the same time ensuring that the water doesn’t “steam off,” which would concentrate the electrolyte and cause thermal runaway?
Yes!! The best way to reduce heat and increase HHO production is to divide the voltage applied to the cell by using more than one cell in series, or in other words several cells connected in a daisy-chain across the battery. With two cells, each will get about seven volts across it and the gas production will be doubled. If space in the engine compartment allows, a chain of six cells can be used which means each receives about two volts and the waste power is reduced to an absolute minimum – while the gas production is six times higher. With the higher rate of gas production, it would probably be possible to reduce the chosen current flowing through the cell (good for smaller batteries and alternators such as in gas scooters and go carts).
Let’s summarize the advantages of the Multi-Cell Setup:
Multiply HHO productionReduced heat by dividing the voltage inputMinimize the chance of Thermal Runaway
¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤
You won’t find a more complete Multi-Cell Generator System
with higher output at this price.
Don’t be misled by Price over Quality
¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤
DARE TO COMPARE
WHAT KempCo HAS!
WE OFFER
Quality in Craftsmanship:
How many twisted wire wraps are there for highest HHO output?
And how low are they on the tower?
(They only produce when they are beneath the electrolyte level)
Quality of Materials & Components
What are the components made of? Is it 316L and 18/8 Stainless Steel?
(We use only 316L wire and 316 hardware under the lid, including the bolts!)
Are you getting what you pay for???
Quality in overall Care and Customer Support
What happens when there are questions? Who will be there to address concerns?
How Well Do ”Water4Gas” Style Generators Work?
Media outlets around the country have answers…
Oregon man increases his gas mileage with HHO in this news report!
See how a man in Norfolk, VA doubled the mileage on his Avalanche!
♦ KempCo’s Hydrogen Generator Cell Units ♦
Based on the original “Water4Gas style”, our Generators have multiple improvements including more than
twice the amount and a higher grade of stainless steel wire, superior lid connections and vastly
increased HHO output (over 300ml as an individual cell),
these Next Generation Cell Units greatly surpass the original design,
when multi-linked produce more than 350ml. each, that’s almost 3/4L for this Two Cell System.
With the highest quality materials including
316-grade Hardware and 316L-grade Stainless Steel Wire in the electrolyte chamber,
you can be assured these Generators are not only built to perform, they’re built to last.
— Easy to Maintain —
KempCo prefers this style of hydrogen generator,
being so much easier to maintain than the steel plate, wire bolt or washer style units.
A clean Cell produces more HHO and cleaning a KempCo “High Output” Generator is easy
with just plain water and a small plastic bristle brush.
— New Twist~Connects —
allow for smooth removal and replacement of the Generator Cells from your vehicle.
The Twist~Connects also make periodic “topping off” of your generator with distilled water
a real breeze!
— High Quality, Long Life! —
We apply the same craftsmanship in the construction of our Generators as we do to all our HHO products.
Using over 600″ of the Highest Grade, Custom Annealed 316L Stainless Steel Wire.
Our twisted four strand design for both positive and negative electrodes allows you to reverse the wiring
adding even more life to your generators, and our 5mm electrode spacing is optimum for hydrogen production.The redesigned lids with custom gaskets has eliminated the #1 problem of ineffective draw and hydrogen leakage.
These “Fully Assembled” units measure 4 inches wide and 7¾ inches tall at the top of the color coded wing nuts.
♦ KempCo’s Multi-Cell Systems ♦
come ready and easy to install
Each individual Cell Unit is precision made, assembled and ready to be adapted to your chosen System location.
While all vehicle locations for the Generators placement will vary, one thing is certain: for any Multi-Cell System,
each Individual Cell needs to be linked together before hooking up to the engine.
— Here’s KempCo’s Solution! —
To help with your installation and also to aid in the periodic maintenance of your Cell Units,
KempCo provides enough 1/4″ hose and Twist~Connects for you to inter-link the individual Cells vacuum draw.
And that’s not all;
we’ve also decided to throw in 16 gauge wire and spade connectors for you to wire (in series) all Cell Units together.
All of this adds up to what we consider a “Complete Cell System”.
— Now —
Your custom pre-wired and vacuum-linked (with Twist~Connects) “Multi-Cell System”
is ready for the Hook-Up to the vehicles engine.
And with Twist~Connects you’ll not only appreciate the ease of maintenance during routine cleaning,
you’ll be eliminating wear and tear on your lid connections, vacuum hose, and barbed fittings from
their otherwise continued removal and replacement.
For Frequently Asked Questions
See our store Page here
Provided FREE with your purchase:
♦ 2 - Feet of ¼” Vacuum Line (for inter-linking the Cells with Twist~Connects)
♦ 2 - Male ¼” Barbed Twist~Connect fittings (for vacuum line inter-linking)
♦ 2 - Female ¼” Barbed Twist~Connect fittings (for vacuum line inter-linking)
♦ 1 - Foot of 16 gauge electrical wire (for electrode inter-linking)
♦ 4 - Locking Spade Terminals (for electrode inter-linking)
♦ 4 - Inches of Shrink Tube (for wire to terminal connections)
Your Purchase Includes
Two Fully Assembled Generators
Consisting Of:
♦ Two - Precision cut and glued Plexiglas Towers, each wound with over 600″ of
our our Custom Four Strand Twisted .035 diameter 316L Stainless Steel Wire
♦ One – “Starter” Generator Lid fitted with an Air-Intake Bubbler, a One-Way
Safety Relief Check Valve and One ¼” Elbow Supply Hose Connector,
all reinforced with Stainless Steel
♦ One - ”Add-On” Generator Lids each fitted with Two ¼” Elbow Supply
Hose Connectors, all reinforced with Stainless Steel
Note: Both “Starter” and “Add-On” Generator Lid Assemblies are Hydrogen-
Tight Sealed and thru-bolted with 316-grade Stainless Steel Hardware
below the lid and 18/8-grade Stainless Steel hardware above the lid.
Not only does this ensure a tight corrosion resistant connection to the
Generator Cell Tower, it also means they’re built to last.
♦ Two - Quart size ” Ball” jars
♦ Two - KempCo Custom Jar Lid Gaskets (for a hydrogen tight seal)
Plus the KempCo-HHO “Dual Supply” Hook-Up Kit:
8 – Feet of 1/4″ Automotive Vacuum Hose
1 – Universal Tee (1/8″ to 1/2″) w/Hose Clamps for Vacuum Source Splice
1 - Barbed Thru-Hull 1/4″ Hose Fitting for Cold Air Intake Connection
1 – Barbed Tee (1/4″) for Supply Source Splice
2 – High Flow In-Line Check Valves
1 – Two Piece (male & female) Twist~Connect
4 - Feet of 14-gauge Red (positive) Automotive Hook-Up Wire
2 – Feet of 14-gauge Black (ground) Automotive Hook-Up Wire
1 – Inline Blade Style Fuse Holder w/15amp Fuse
1 - Ring Connector (1/4″ ID)
2 – Butt Connectors
2 – Locking Spade Connectors
1 – Inline Wire Splice Terminal
8 - Inches Shrink Tubing
6 – Assorted Cable Ties (to help secure hoses and wiring)
Top-Off Kit:
1 – Eight Ounce Squeeze Bottle
1 – Yorker (graduated tip) Style Cap w/Hose
1 – Male Twist~Connect
And - at No additional charge
to pre-wire and vacuum-link the Cells:
♦ 2 - Feet of 1/4″ Vacuum Line
(for inter-linking the Cells with Twist~Connects)
♦ 2 - Male 1/4″ barbed Twist~Connect fittings
(for vacuum line inter-linking)
♦ 2 - Female 1/4″ barbed Twist~Connect fittings
(for vacuum line inter-linking)
♦ 1 - Foot of 16 gauge electrical wire
(for electrode inter-linking)
♦ 4 - Locking Spade Terminals
(for electrode inter-linking)
♦ 4 - Inches of Shrink Tube
(for wire to terminal connections)
Your purchase is complete with
A detailed step-by-step Installation & Maintenance Instruction Manual
(with pictures and diagrams) via .pdf file upon shipment of item;
you’ll also get tips and suggestions on various wiring schemes to keep your generators cool
and maximize the HHO Output.
Remember, that KempCo stands behind it’s products and is always available if questions arise.
Additional parts that you will need
for the Hook-Up of your new Multi-Cell System,
are available from most local hardware and/or auto parts stores.
If there are parts you do not have in your garage or cannot locate, or just for your convenience,
Visit the KempCo eBay Store
Here you’ll find various Hook-Up Kits, DIY items
and related products for this installation or other projects. Our kits show a list of supplies to cross-check
first against those parts and supplies you may already have available.
In order to see significant mileage gains
for fuel injected vehicles,
will you need a MAP Sensor “Enhancer”?
If your vehicle is fuel injected and has an oxygen sensor and a factory MAP/MAF sensor,
which is pretty much all vehicles ‘96 and newer and some as far back as ‘86,
a means of communicating with the vehicle’s computer is necessary
to explain the (now) cleaner emissions.
The emissions are what the oxygen sensor reads, and are then deciphered and passed on
by the engine’s factory MAP/MAF sensor to the vehicle’s ECU (Engine Control Unit),
which, among other tasks, is constantly adjusting the fuel injectors
to deliver the proper fuel-to-air ratio.
The addition of a hydrogen on demand system adds more oxygen to that mixture
and skews the reading delivered to the factory MAP/MAF sensor.
This reading is perceived by the ECU as a “lean” condition in the combustion chamber,
which unnecessarily tells the injectors to pump more fuel into the engine,
very counter-productive to say the least!
That’s where the MAP Sensor “Enhancer” comes in
An 0² extender for your oxygen sensor can help but will not
let you adjust (“enhance”) the reading that the engines MAP sensor delivers to the ECU so
that it will more closely resemble the factory setting.
Long story short!
Whether you try just an 0² extender,
an 0² extender with a MAP Sensor “Enhancer”, or
a MAP Sensor ”Enhancer” by itself,
most 1996 or newer vehicles, and some back to 1986 with a MAP or MAF Sensor
will need some form of adjustment to alter the information that the ECU receives.
Without this,
one may not see all the gains possible using any
Hydrogen on Demand System.
To view what KempCo has to offer
Including our:
Dual-Edge Map Sensor Enhancer (DEMSE),
Visit Our eBay Store
We take pride in what we build!
¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤
Some of the remarkable benefits from using our
Hydrogen On Demand Generator System:
— Affordable and easy to install —— Increases your gas mileage and saves you money! —— Cleaner emissions which help to protect our environment —— Eliminates carbon deposits from inefficient combustion —— Faster acceleration, with more engine power —— Eliminates (low octane) knock and ping —— Will work in freezing temperatures —— Works on 99% of new and used vehicles —— Has been successfully used around the world —
♦ Backed by KempCo’s 100% Satisfaction Guarantee!! ♦
Payment
KempCo-HHO accepts PayPal as our method of payment. We ask you to pay within 3 days of purchase of Buy It Now, or close of auction. We are also PayPal and ID icon Verified, so buy with confidence. KempCo’s number one priority is customer satisfaction, as expressed by our Seller Feedback. KempCo-HHO sells to customers nationwide and around the globe. We look forward to seeing you as another satisfied customer, added to our worldwide Store Map!!
Shipping
Purchases usually ship within 2 business day of receiving your cleared payment. We use USPS or UPS Mail services. You can use the eBay shipping calculator to choose your preferred shipping method. Or you may wait for an invoice and allow us to figure the lowest priced shipping method and your total costs.Items are calculated with the lowest shipping prices for quantity, weight and destination of item(s) purchased. For multiple item purchases, we will combine shipping. Your item(s) are securely packed with care to insure their safe arrival. We now ship Worldwide. For this item, all International and Domestic purchases will have insurance included in the shipping costs. International customers should wait for an invoice before paying in order for us to calculate correct totals for purchase and shipping. International buyer assumes all responsibility for any customs fees of shipment entries into their country. International Buyers; Please Note: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility. Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up; do not confuse them for additional shipping charges. We do not mark merchandise values below value or mark items as “gifts”; – US and International government regulations prohibit such behavior.
Terms of Sale
Remember, HHO systems and designs (although not new) are still considered experimental. We trust it and believe in HHO technology, but we cannot take responsibility for your use or misuse of the product. Use or install it at your own risk, or have your qualified mechanic do so for you. This product comes with our 14-day refund policy. If our product does not arrive as described or your are not happy with your purchase, please contact us promptly for return authorization. Your satisfaction is of utmost importance. We will be happy to exchange your purchase or refund your purchase price (less shipping). The item must be returned within 14 days of receipt. Refund will be given after receipt of return. You can buy with confidence; we are PayPal and ID icon verified.
About Us
KempCo Industries is a green-conscious, family owned and operated business dedicated to bringing you the highest quality products at competitive prices. We firmly believe in Hydrogen-On-Demand and associated products. The concept of cleaner air for our future is now a reality, one mile per gallon at a time. Through adventurous minds and dedicated applications we can all make a difference. We hope to earn your recognition as a trusted supplier of HHO and related products. We really appreciate what our satisfied customers have to say, check out our Seller Feedback!
I will be calling this one,”THE SUPER CELL” Excellent workmanship! HHO Hydrogen Cell Tower w/Hardware & Jar Seal
I will Buy again! Excellent Quality, Next day shipping, A++ to do business with. Hydrogen Generator Starter Cell HHO Water4Gas Style
Unlike the other transaction with another supplier, the 316L SS wire was pliable 150′ 316L .035 Stainless Steel Wire HHO Water4Gas
great product! bhig thanks again from HydroPower4Cars 300′ 316L .030 Stainless Steel Wire HHO Water4Gas
THIS IS THE BEST EBAY TRANSACTION EVER FOR ME! A++++++++Marty, many thanks! HHO Hydrogen Generator Cell Tower, Hardware & Jar Seal
This HHO Tower is THE BEST I’ve seen & works GREAT!!!! THANKS!!! HHO Hydrogen Generator Cell Tower, Hardware & Jar Seal
This seller is a 10! and gives BEST service on EBAY! simply can’t be beat! A+++ 300′ 316L .030 Stainless Steel Wire HHO Water4Gas
clearly a dedicated ebayer. Excellent delivery time 2days A++++++ HHO Stainless Steel Wire 150′ .035 316L Water4Gas
Good Parts as described! LIGHTNING FAST SHIPPING!!!! THANKS!!!!!! KempCo-HHO PCV Enhancer–HHO Hydrogen Water4Gas
Great item. Fits just right solves leak problem, I’ll be back! HHO Water4Gas Hydrogen Generator (12) Jar Lid Gaskets
THE BEST TOWERS I HAVE SEEN Hydrogen Generator Towers (4) Water4Gas HHO–Free Ship
Easy transaction, will buy from kempco4 again. A+++ HHO Water4Gas Hydrogen Generator Gasket 4 Ball Jar Lid
«:::A:::» «:::W:::» «:::E:::» «:::S:::» «:::O:::» «:::M:::» «:::E:::» 5 STARS HHO Hydrogen Generator Cell Tower Complete w/ Hardware
Outstanding product. Very fast shipping. Great instructions included. A+++++++++ HHO Generator Parts (2) 1/4″ High Flow Check Valves
Excellent product, great price, fast shipping! Five Stars!!! 100′ 316L .030 Stainless Steel Wire HHO Water4Gas
everything worked great, great seller, will buy from again, thanks very much. KempCo-HHO PCV Enhancer–HHO Hydrogen Water4Gas
great store for HHO parts, great price, super fast shipping a++++++ HHO Water4Gas (2) Ball Jar Wide Mouth Lids Plus Seals
This seller is top gun the best AAAAAAAA++++++++ looking forward to deal again. 50′ 316L .045 Stainless Steel Wire HHO Water4Gas
VERY, VERY GOOD SELLER, YHANK YOU AAA++++ HHO Hydrogen Generator Cell System Water4Gas Style
Great Response to Questions!!! Super Fast Shipping!!! Excellent Product!!!!!!!!! Hydrogen Generator Tower(1)Water4Gas HHO–Free Shipping
Another great transaction.Thank you for great service & quality merchandise. 300′ 316L .035 Stainless Steel Wire for HHO Generator
good quality and well made HHO Hydrogen Generator Water4Gas (1) Cell Tower Plus
same day mailing! exceptional product. good communication. 5 stars plus on all!! 100′ 316L .030 Stainless Steel Wire HHO Water4Gas
Great Seller Super Fast Shipping A+++ hho tower was Awesome Thanks Hydrogen Generator Tower(1)Water4Gas HHO–Free Shipping
A+++ Excellent HHO Hydrogen Generator Cell Tower, Hardware & Jar Seal
FAST SHIP GREAT COMMUNICATION !!! A+++ FREINDLY E-MAILS HHO Hydrogen Generator Water4Gas(10)Safety Check Valve
The Items were received as stated and were quite well made. Shipping was fast. HHO Hydrogen Generator Cell Tower, Hardware & Jar Seal
Stellar seller. As described, quick shipping, well packed, communicates. 200′ 316L .030 Stainless Steel Wire HHO Water4Gas
Contact Us
If you have any questions about what we sell, or products that are hard to find, simply email us at kempco@yahoo.com and we will be happy to reply as soon as possible. We strive to provide first-rate 5 Star ***** customer service and support.
|
